6530A REV E Norge Washer Parts List

Leveling foot (2.5" long dryer leveling leg)

The adjustable leveling leg is used to support and keep your dryer level. It also allows you to adjust the height of your dryer. You may need to replace the leveling leg if one becomes lost, the thread is stripped off, or it is noisy during operation. The leveling leg is almost 2” long, white in color, and made of plastic. There are four leveling legs used on the dryer, please order quantity needed as they are sold individually. This is a genuine OEM part.

Refrigerator shelf frame with glass (shelf, snack pan)

Ice guide

This ice guide is in the freezer door located in the dispenser section. This part helps the ice be guided from the dispenser to your cup once activated. If the ice maker will not dispense ice, or the locking tabs are broken on the guide, you may need to replace the ice guide. The ice guide is made of clear plastic and is a genuine OEM part. Please remember to disconnect the power and water supply before starting your repair.

Roller support tri-ring (single tri ring)

The tri ring is used to hold the drum support rollers or the idler pulley onto the shaft. If your dryer will not tumble or is noisy, you may need to replace the tri ring. This is a genuine OEM part and is sold individually.

Crisper drawer (pan, crisper)

The crisper drawer is used for storing fruits and vegetables at a humidity level that will help them stay fresh longer. If the crisper drawer is damaged, you may need to replace it. This crisper drawer is made of clear plastic and measures 12.847" depth by 15.217" width by 6.93 height. This part is sold individually and does not come with the plastic faceplate on it. If your current crisper drawer has one, you will need to remove it and transfer it to the new crisper drawer. NOTE: As per the manufacturer, the crisper drawer has been updated from the original. A new crisper cover may need to be purchased for the drawer to work.

Drive belt - 51 inches long (washer drive belt)

This V-style drive belt is about 51-inch long and 3/8-inch wide. This part is made to slip onto the motor pulley to bring the basket up to the speed required. The belt encounters wear and tear over time. If your washer will not drain, spin, or agitate, you may need to replace your belt. It is recommended to disconnect the power to your washer before you start your repair. This V-style belt is a genuine OEM part.

Complete lower service rack assembly (rack low roll asm)

This dish rack is for dishwashers. Dish rack holds the dishes in place during the dish washing cycle.

Defrost heater harness kit (heater harness def asm)

This dual heater kit replaces the single heater. It's redesigned to use two heating elements for a better defrost cycle.

Selector knob with clip (knob & clip asm wh)

This knob accepts a D-shaped shaft. Sold individually.

Defrost timer (use wpl 482493)

This 120 volt, 60Hz defrost timer acts like a clock, continually advances and alternates between activating the cooling cycle and the defrost heater. If the refrigerator is too warm, freezer section too warm or freezer not defrosting you might need to replace the defrost timer. This is a genuine OEM part. Disconnect the power to the refrigerator before starting the repair.

Rotary start switch (start switch)

This part is used to start the dryer once you have selected a setting on the timer. The terminal locations on the new switch may be different, match up terminal numbers from old switch to new.

Door cam - black (lower door cam)

The refrigerator uses a set of cams to help with the closing of the doors and help to keep them in position. These cams are mounted around the door pivot point and are made up of a series of ridges and valleys to help keep the door in position. If your refrigerator uses a door closer, the door should shut all by itself. This part is black in color, made of plastic, and is sold individually. This is a genuine OEM part. Note: As per the manufacturer a new screw is needed to mount the door cam. This door cam is sold individually.

Agitator coupling kit (scr 1/4-20 mch 5/8 s)

This is a washing machine agitator coupling kit also known as an agitator drive belt. It connects the transmission drive shaft to the agitator base. It includes the couple, gasket, and bolt. If the teeth on the coupler is worn out it will cause the agitator not to turn and will need to be replaced. This is a genuine OEM part. Please remember to disconnect the power before starting your repair.

Evaporator fan grommet - red (grommet evap fan)

This red evaporator fan motor grommet provides a cushion between the fan motor and the motor mounting bracket. If the grommet is damaged and you are getting noise from the fan motor, you may need to replace it. This is an OEM part sourced directly from the manufacturer. Please remember to disconnect the power to the refrigerator before starting your repair.

Light bulb (lamp)

This 10W - 120V light bulb is used on the inside of your dryer to provide light when the door is open. It is clear in color and has a standard screw-in base. If your current bulb is burnt out or broken you will need to replace it. This bulb is a genuine OEM part and is sold individually.